Pozdrav kolege!
Evo me opet nakon dugo vremena. Odmakao sam se od popravaka kućanske elektronike pa me nije dugo bilo. Ženina sestra je izgleda malo forsirala indukciju pred Uskrs :) Pojavila se greška E4. Opis stoji "Greška u konfiguraciji ploče za kuhanje". Ima 2 "ringle" i samo veća joj ne radi. Odnosno kad pokuša uključiti veću, ova greška se pojavi. Da li imao netko kad ovakav problem? O čemu se tu zapravo radi? I naravno kako se otkloni greška?
Ja sam pretražio po internetu kakve to mogu biti konfiguracije i slično, ali nikakvih korisnih informacija. A moja 3-4 popravka indukcija mi ne daju ni blizu dovoljno iskustva da sam zaključim.
Hvala i srećan Uskrs!!!!
Indukcija Gorenje IT320AC greška E4
Urednici: goranfri,nike,Honorarac,sim
Pravila foruma
BT-expert info - BTexpert forumi
U naslov teme prvo pisati ime proizvođača, zatim oznake modela bez crtica i razmaka i kratak opis kvara. U post obavezno upisati ID ili EAN oznake sa poleđine aparata u suprotnom tema će biti obrisana.
Praktikujemo da na kraju opišemo kako smo rešili problem. Zatim zatvorimo temu >UPUTSTVO<
PRILIKOM POSTAVLJANJA PITANJA U VEZI ELEKTRONSKOG MODULA OBAVEZNO POPIŠITE SVE OZNAKE sa ploče i sa nalepnica, dobro bi došla i po koja fotografija.
BT-expert info - BTexpert forumi
U naslov teme prvo pisati ime proizvođača, zatim oznake modela bez crtica i razmaka i kratak opis kvara. U post obavezno upisati ID ili EAN oznake sa poleđine aparata u suprotnom tema će biti obrisana.
Praktikujemo da na kraju opišemo kako smo rešili problem. Zatim zatvorimo temu >UPUTSTVO<
PRILIKOM POSTAVLJANJA PITANJA U VEZI ELEKTRONSKOG MODULA OBAVEZNO POPIŠITE SVE OZNAKE sa ploče i sa nalepnica, dobro bi došla i po koja fotografija.
-
- gx
- Postovi: 298
- Pridružen: 29 Jun 2016, 15:07
- Location: Umag
- Contact person: Dragan
- Specialty: consumer
Indukcija Gorenje IT320AC greška E4
Iskustvo je direktno proporcionalno kolicini unistene opreme............
- bracans
- bela tehnika
- Postovi: 431
- Pridružen: 19 Apr 2014, 12:49
- Location: Novi Sad
- Specialty: whitegoods
Re: Indukcija Gorenje IT320AC greška E4
CONFIGURATION OF DOMINO BASIC INDUCTION
Configuring is necessary when changing the IHE (induction heating element), or when the display shows E4.
Procedure is the following:
Hob shall be switched off.
Press and hold the sensor key Stop/go (second from the right) and successively press the three left sensor keys (in the sequence: timer, "-", "+"). Sound signal is heard at each press.
Display shows C (flashing) and 0. Hob locking sensor diode flashes, too. Press again and hold the key Stop/go until sound signal is heard i.e. display shows “C” for non-configured and “-" for configured cooking zone.
Put a pot on non-configured coking zone and press sensor key "+" for this zone. “C” changes into "-".
The above mentioned procedure shall be carried out for each cooking zone until the configuration menu after the configuration of the last cooking zone automatically terminates.
ATTN: how to reset the configuration?
When inside the configuration menu (configured and non-configured IHE are shown), it is necessary to press one of sensor keys “minus” for a few seconds (sound signal is heard). “E” will flash on displays for some time, and then two “C” appear. Now configuration can be carried out again.
Mozda pomogne.
Configuring is necessary when changing the IHE (induction heating element), or when the display shows E4.
Procedure is the following:
Hob shall be switched off.
Press and hold the sensor key Stop/go (second from the right) and successively press the three left sensor keys (in the sequence: timer, "-", "+"). Sound signal is heard at each press.
Display shows C (flashing) and 0. Hob locking sensor diode flashes, too. Press again and hold the key Stop/go until sound signal is heard i.e. display shows “C” for non-configured and “-" for configured cooking zone.
Put a pot on non-configured coking zone and press sensor key "+" for this zone. “C” changes into "-".
The above mentioned procedure shall be carried out for each cooking zone until the configuration menu after the configuration of the last cooking zone automatically terminates.
ATTN: how to reset the configuration?
When inside the configuration menu (configured and non-configured IHE are shown), it is necessary to press one of sensor keys “minus” for a few seconds (sound signal is heard). “E” will flash on displays for some time, and then two “C” appear. Now configuration can be carried out again.
Mozda pomogne.
Svastara https://elektroigor.blogspot.com/
-
- Slične teme
- Odgovori
- Pregledano
- Zadnji post
-
-
Gorenje IT 612 SY2B indukciona ploca greska E5 [ODUSTAO]
napisao bokin021 » 09 Apr 2016, 16:02 » u OSTALI APARATI - 12 Odgovori
- 7468 Pregledano
-
Zadnji post napisao cudan
20 Mar 2023, 11:22
-
-
- 3 Odgovori
- 78 Pregledano
-
Zadnji post napisao Kobac
24 Apr 2024, 22:24
-
- 2 Odgovori
- 1002 Pregledano
-
Zadnji post napisao Japanac
24 Dec 2020, 00:14
-
- 2 Odgovori
- 755 Pregledano
-
Zadnji post napisao cudan
19 Jan 2022, 12:25
-
- 3 Odgovori
- 597 Pregledano
-
Zadnji post napisao pandur
12 Jun 2023, 22:10
-
- 5 Odgovori
- 3030 Pregledano
-
Zadnji post napisao elektrosok
28 Mar 2015, 08:53
-
- 9 Odgovori
- 4356 Pregledano
-
Zadnji post napisao junuzovic
01 Jul 2019, 09:23