Ariston Margherita2000 AL128D Ležajevi i semering - REŠENO

[orion52]

Molim ako netko zna,koji ležajevi i semering bubnja idu na ovu mašinu.U nedavnom postu od Munje primjetio sam da je naveo
kako je doktorirao na Aristonovim mašinama.Možda bi mi on mogao pomoći? Inače,tražio sam u pretragi,ali nema ovog modela.Pozzz

[vlajkosdb]

Semering;
Spoljasnji precnik: 75mm, Unutrašnji precnik: 35mm, Debljina: 10mm, Tip: G - 35x62-75x7-10
Spoljasnji precnik: 65mm, Unutrašnji precnik: 30mm, Debljina: 10mm
Lezaj;
Unutrašnji precnik: 25mm, Spoljasnji precnik: 52mm, Širina: 15mm, Tip: 6205-2Z SKF
Unutrašnji precnik: 20mm, Spoljasnji precnik: 47mm, Širina: 14mm, Tip: 6204ZZ SKF
Unutrašnji precnik: 30mm, Spoljasnji precnik: 62mm, Širina: 16mm, Tip: 6206ZZ SKF
Ima dve serije mehanizma,evo pa citaj:
From serial no. 40428.0001, all Slim range models produced in the Comunanza factory have been equipped with a two-bearing mechanism in place of the single-bearing one.
The Service codes of the new mechanism are:
Service code C00096186 - SEAL RING CV4;
Service code C00002591 - BEARING 20X47X14 6204 SKF;
Service code C00013563 - BEARING 25 X52 X 15 6205 - 2Z SKF;
Service code C00110340 - CROSS WITH SEAL RING (2C) SNELLA;
Service code C00094289 - EVO 40L TANK SLIM (1-C) > (2-C)EVOII;
Service code C00094290 - OUTER- SET 40 L.(1-C)>(2-C)EVOII;
Service code C00064527 - DRIVEN PULLEY CONE D=280 MM H= 17MM;
Service code C00066080 - DRIVEN PULLEY CONE D= 210 MM H=17 MM.

The tank assembly with the new two-bearing cross has the same Service code as the single-bearing one (C00094289); the latter will be available until stocks run out.
When replacing the tank, make sure that the value H (17 mm or 25 mm) of the basket cross shaft corresponds to the value H of the pulley (see Fig.001).

The following premodified items will continue to be used:
Service code C00026298 - BEARING BA2B 633667 30X60.03X37;
Service code C00039667 - SEAL RING;
Service code C00074137 - CROSS WITH SEAL RING;
Service code C00081875 - DRIVEN PULLEY D=280MM H=25MM;
Service code C00074138 - DRIVEN PULLEY D = 210MM H=25MM;
Service code C00026299 - SEEGER RING SB 60X1,5.

[orion52]

Zahvaljujem,Vlajkosdb,na trudu i opširnom izlaganju,ali po servisnim kodovima vidim da postoje 3 vrste ležajeva i 2 vrste semeringa
od kojih neznam koji su u igri na dotičnom modelu.Zato prilažem servisne brojeve,koji su otisnuti na vratima mašine,ako nešto pomogne
da bi se definirali točni ležajevi i semering.Pozzz
S/N 310273776 80249030230

[orion52]

Pokušavam označiti temu rješenom,ali kako nema oznake "uredi" ,izgleda mi nerješivo.Stoga molim administratora za pomoć-ili da ubaci oznaku
"uredi",ili da u početni post upiše "rješeno".Hvala.Pozzz